- Advertisement -
VPS House Servers
VPS House Servers
VPS House Servers

10 Useful IP Commands to Configure Network Interfaces

In this post, we are going to review how we can assign Static IP Address, Static Route, Default Gateway etc. Assigning IP Address on demand using IP command. IFCONFIG command is deprecated and replaced by IP command in Linux. However, IFCONFIG command is still works and available for most of the Linux distributions.

How do i Configure Static IP Address Internet Protocol (IPv4)

For RHEL/CentOS/Fedora

Open and edit network configuration file for (eth0 or eth1) using your favorite editor. For example, to assigning IP Address to eth0 interface as follows.

Simple output:

- Advertisement -
VPS House Cloud Servers
VPS House Cloud Servers
VPS House Cloud Servers

DEVICE="eth0"
BOOTPROTO=static
ONBOOT=yes
TYPE="Ethernet"
IPADDR=192.168.50.2
NAME="System eth0"
HWADDR=00:0C:29:28:FD:4C
GATEWAY=192.168.50.1

For Ubuntu/Debian/Linux Mint

Assign Static IP Address to eth0 interface editing configuration file /etc/network/interfaces to make permanent changes as shown below.

auto eth0
iface eth0 inet static
address 192.168.50.2
netmask 255.255.255.0
gateway 192.168.50.1

Next, restart network services after entering all the details using the following command.

1. How to Assign a IP Address to Specific Interface

The following command used to assign IP Address to a specific interface (eth1) on the fly.

Note: Unfortunately all these settings will be lost after a system restart.

2. How to Check an IP Address

To get the depth information of your network interfaces like IP Address, MAC Address information, use the following command as shown below.

Sample Output

1: lo: mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
link/ether 00:0c:29:28:fd:4c brd ff:ff:ff:ff:ff:ff
inet 192.168.50.2/24 brd 192.168.50.255 scope global eth0
inet6 fe80::20c:29ff:fe28:fd4c/64 scope link
valid_lft forever preferred_lft forever
3: eth1: mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
link/ether 00:0c:29:28:fd:56 brd ff:ff:ff:ff:ff:ff
inet 192.168.50.5/24 scope global eth1
inet6 fe80::20c:29ff:fe28:fd56/64 scope link
valid_lft forever preferred_lft forever

3. How to Remove an IP Address

The following command will remove an assigned IP address from the given interface (eth1).

4. How to Enable Network Interface

The “up” flag with interface name (eth1) enables a network interface. For example, the following command will activates the eth1 network interface.

5. How to Disable Network Interface

The “down” flag with interface name (eth1) disables a network interface. For example, the following command will De-activates the eth1 network interface.

6. How do I Check Route Table?

Type the following command to check the routing table information of system.

Sample Output

10.10.20.0/24 via 192.168.50.100 dev eth0
192.168.160.0/24 dev eth1 proto kernel scope link src 192.168.160.130 metric 1
192.168.50.0/24 dev eth0 proto kernel scope link src 192.168.50.2
169.254.0.0/16 dev eth0 scope link metric 1002
default via 192.168.50.1 dev eth0 proto static

7. How do I Add Static Route

Why you need to add Static routes or Manual routes, because that the traffic must not pass through the default gateway. We need to add Static routes to pass traffic from best way to reach the destination.

8. How to Remove Static Route

To remove assigned static route, simply type the following command.

9. How do I Add Persistence Static Routes

All the above route will be lost after a system restart. To add permanent Static route, edit file /etc/sysconfig/network-scripts/route-eth0 (We are storing static route for (eth0) and add the following lines and save and exist. By default route-eth0 file will not be there, need to be created.

For RHEL/CentOS/Fedora

For Ubuntu/Debian/Linux Mint

Open the file /etc/network/interfaces and at the end add the persistence Static routes. IP Addresses may differ in your environment.

auto eth0
iface eth0 inet static
address 192.168.50.2
netmask 255.255.255.0
gateway 192.168.50.100
#########{Static Route}###########
up ip route add 10.10.20.0/24 via 192.168.50.100 dev eth0

Next, restart network services after entering all the details using the following command.

10. How do I Add Default Gateway

Default gateway can be specified globally or for in interface-specific config file. Advantage of default gateway is If we have more than one NIC is present in the system. You can add default gateway on the fly as shown below command.

Kindly correct me if i missed out. Please refer manual page doing man ip from terminal/command prompt to know more about IP Command.

- Advertisement -

There are no comments yet

  • Hello, guest